How to Keep Led Strip Lights From Falling Off

Table of Contents

The popularity of strips has grown in recent years. These lights are great for accenting and highlighting certain features, such as a fireplace or aquarium but there’s one problem- they tend to fall off when you need them most!

5 Common Reasons Why Led Strip Lights Keep Falling Off

1. Dust or Debris on The Surface

Dust and dirt can also cause strips to fall off. Make sure you clean them regularly to keep them free from dust and dirt.

2. Improper Installation

One of the most common reasons why strips keep falling off is that they are not installed properly. Make sure that the strips are attached securely to the surface you are using them on.

3. Poor Quality Adhesive:

Another reason why strips may fall off is because of a poor-quality adhesive. When choosing an adhesive, make sure to select one that is specifically designed for use with LEDs.

4. Excessive Heat Issues

Strips can generate a lot of heat, and if they’re not properly ventilated, this can cause them to fall off. Make sure that there is plenty of space around the strips and that they’re not near any heat sources.

5.  Environmental factors: Moisture-Water Damage

Strips are susceptible to moisture, so if they’re installed in a damp environment, they’re likely to fall off. Make sure that they’re installed in a dry location and that any moisture is eliminated before powering them on.

Instructions: How To Keep Led Strip Lights From Falling Off

1. Clean Your Surface

Clean the surface where the strip will be attached. Make sure the surface you are sticking the strip to is clean and free of dust, dirt, or any other debris. This will help the adhesive stick better and keep the strip in place.

2. Apply Strong Adhesive

 Use double-sided tape or velcro to attach the strip to the surface. This will help keep it in place and prevent it from falling off.

3. Position in Right Place: 

Position the strip in the right place before pressing down. Make sure it is straight and aligned correctly before adhering to the surface.

4. Press Down

Press down on the strip firmly to make sure the adhesive sticks to the surface and holds it in place. Wait a few minutes for it to dry completely before testing it out.

5. Let Them Dry

Let the strip dry for a few minutes before turning it on or using it. This will ensure that it stays in place and does not fall off.

6. Final Test

Turn on the strip and test it out to make sure it is working properly. If everything looks good, then you’re all done!

Additional Tips To Prevent Strip From Falling Off

1. Using Hot Glue

When using hot glue, make sure that the strip is properly aligned before gluing it in place. This will help to prevent it from slipping off or becoming crooked.

2. Try To Manage OverHeating

If the strip starts to overheat, try to remove it from the heat source and allow it to cool down before continuing. This will help to prevent damage to the strip.

3. Using A Protective Base

If possible, use a protective base such as a piece of metal or Plexiglas underneath the strip. This will help to keep it in place and protect it from any accidental damage.

4. Cut Them into Little Sizes

Cut the strip into smaller sizes before attaching it to the channel. This will make it easier to work with and less likely to fall off.

5. Mount Them on a Channel

Mount the strip onto a channel or other holder if needed so that it is less likely to move or fall off.

How to Conceal Led Strip Lights in Ceiling?

When installing a strip light in your ceiling, there are a few things you can do to conceal the light and make it look more professional. One option is to install the light in a recessed can. This will conceal the light and give it a finished look. You can also use a decorative trim ring to cover the edge of the light. This will make the light less visible and give your ceiling a finished appearance.

How To Hang Led Strip Lights on the Wall Without Damaging? 

To hang strip lights on the wall without damage, you will need:

Led strip lights 

Screws 

Drill 

Tape measure 

Level 

Pencil 

Paint or a marker to mark the wall

1. Decide where you want to hang your led strip lights. Use a tape measure to find the correct height and width. Make sure it is even on both sides. Mark the spot on the wall with a pencil.

2. Drill pilot holes into the wall where you marked it. The size of the hole should be the same size as the screws that came with your led strip lights. If they don’t come with screws, use a drill bit that is slightly smaller than the screws you plan to use.

3. Screw your led strip lights into the wall. You may need someone to help you hold them in place while you screw them in. Make sure they are level before tightening the screws all the way.

4. Connect your led strip lights to an electrical outlet and turn it on!

Conclusion:

Depending on the application, there are a few ways to keep your LED strip lights from falling off. 

For example, if you want a bright accent light on top of your kitchen cabinets and don’t need any wiring, you can use adhesive to mount the strip light. 

However, if you’re trying to illuminate an entire room, it’s best to install the strips securely into the walls or ceiling so they don’t fall off. 

We hope this article has helped you understand how to keep your LED strip lights in place and achieve the desired effect!

maisie
maisie
Maisie

Hi, I’m the author of this post, and I have been in this field for more than 10 years. If you want to wholesale LED Strip Lights or custom LED Pixel Light, feel free to ask me any questions.

Request A Quote

Need something tailored in a short time? We’ve got a plan for you.